Homepage

1. Engine Basics

2. Advanced Engine Tuning + Forced Induction

3. EFI Tuning

4. Chassis Tuning

5. Misc. Information

6. WHAT'S HOT in Auto

7. New Products + Tools

8. All Wheel Drive Civic Type RL

Contact Us

 

DOT Help

Department of Transpertation

MAP Sensor Vs. MAF Sensor

Contributed By: enginebasics.com

Each EFI car today is equipped with either a MAF sensor ( mass air flow) or a MAP sensor ( manifold absolute pressure). Some cars are even equipped with both a MAF and a MAP sensor…..example a Mitsubishi Evo X. So what do these sensors do and what is the difference?

MAP Sensor

A map sensor is a sensor that is installed somewhere in the intake manifold or very close to it. It is a sensor that detects the pressure found in the manifold. On a naturally aspirated motor this sensor will be detecting the negative pressure found in the intake manifold which we call vacuum. If the car is equipped with Forced Induction, then this sensor will be in charge of not only detecting the vacuum but the actual positive pressure in the manifold as well.

Because this sensor must cover both vacuum and pressure they come in different size measuring ranges. These ranges are often given in the unit of Bar instead of PSI. Bar is the metric unit for pressure while PSI is the standard unit. When choosing a MAP sensor choose a sensor that will be appropriate for the amount of vacuum and pressure your particular motor will see.

MAF Sensor

While there are many kinds of maf sensors let’s focus more on what they are. A maf sensor is a device that measures the mass air flow, hence its name. It measures the mass of air that passes by the sensor and outputs the actual flow of air to the ECU. What can be confusing when dealing with and tuning a maf sensor is that the computer will often interpret the MAF data to depict an actual load value instead of an actual number in CFM of flow. Because of this, MAF sensors can be harder to tune based on the interpretation of the ECU for a given air flow.

MAP sensor VS. MAF sensor

While both sensors accomplish the same thing we could give the +’s of each.

MAP sensor

1. Even if an intake pipe blows off or there is a vacuum hose leak the car will run the same, as the actual manifold pressure will not be any different so you will not be left stranded some where.

2. Sensor reads actual load so there is no guessing what load level the engine is seeing.

MAF sensor

1. The amount of CFM entering the motor is VERY accurate even at low air flow levels. Because of this MAF sensors have a tendency to get better MPG’s (miles per gallon).

2. Most have a built in AIT( Air Intake Temperature ) sensor so you can monitor your actual air intake temps at the sensor.

***Remember*** to check for other relevant information in the columns and article tables.

ATTENTION READER:

If you enjoyed the information and article you just read be sure to check out our newly released book with even more exciting photo's and information:
How to Turbocharge and Tune your Engine

Follow Enginebasics on...

Want to know more about your particular Make and Model vehicle? All of these vehicles are covered in the tech, maintenance and repair articles found above. Enginebasics is the wiki or wikipedia of car part, repair, how to and tuning information. Let us be the class 101 for your automotive learning.

Individual Models

Below are just a few of the articles found here on enginebasics.com

Reading Spark Plugs	Camshaft Understanding	Engine Timing	Intake Runner Length	Exhaust Flow Tuning	Camshaft Timing	Engine Cooling Basics	Compression Testing	Forced Induction
Tuning A/F Ratio Basics	Intake Manifold Basics	A look at cooling mods	Camber Caster Basics	Sequential Vs Batch Injection	Fuel Pressure Regulator	EGT Vs A/F EFI Tuning	Engine Start Programming	What is a fuel Injector?
Brush vs Brushless Motors	4-stroke motor diagram	Crankshafts Basics	Automotive Relays	EFI Tuning Basic Thoery Guide	Understanding Electric Motors	Water Meth Injection	Intercooler Basics	e85 Basics
Water to Air Intercooling	Turbo Surge	EFI Air Intake Temp Tuning	Map vs. MAF Sensor EFI Tuning	Engine Start up tuning for EFI Cars	Building an EFI Surge Tank	Intercooler Efficency	Boost Controllers	Engine Oil Weights
Exhaust Cutout Basics	Cold Air Intake vs Short Ram	Engine HP and Torque Basics	Intercooler Sprayer Basics	Turbo Manifold Design Basics	Cryo Liquid Co2 Cooling	Oil Cooler Basics and Installation	Boost by Gear Tuning	Closed Loop vs Open Loop O2 tuning
Changing your own oil	Static Vs. Dynamic Compression	Air to Air Vs. Water to Air Intercoolers	Vented vs Recirculating Blow Off Valves	Engine Intake Exhaust Valves	Wiring a fuel pump relay	Synthetic vs Regular Oil	O2 Sensor Repair Fix	Embrace the TURBO LAG

**TO SUBMIT AN ARTICLE TO ENGINE BASICS PLEASE CLICK: CONTACT US!

Testimonials Page

“Thank you, for the info, on your site, on how to remove valve springs, and install stem seals, using normal shop tools. Info from every other site I looked at, only said how to do it using costly special tools. Thank you for showing the REAL easy way, and saving me some money.”   Joe S

“Hello there,
            Don’t have any questions, just wanted to say thanks for putting this info out there.  So much mis-information on forums, good to read some solid info. Peace” Jay R.

Privacy policy and terms of service

Advertise

Copyright 2010 EngineBasics.com: Engine Basics. All Rights Reserved

Enginebasics Google+ Page